Whirlpool Troubleshooting Washer: Quick Fixes and Solutions

Is your trusty Whirlpool washer giving you a hard time lately? If you own a Whirlpool washer, you know how convenient it is to have a reliable appliance that can handle all your laundry needs. However, like any other machine, your Whirlpool washer may occasionally encounter some problems that prevent it from working properly. Whether it’s not draining, spinning, starting, or making strange noises, you may wonder what’s wrong with your washer and how to fix it.

Don’t worry, we’re here to help. In this article, we’ll show you some of the most common Whirlpool washer issues and how to troubleshoot them using simple steps and tools. We’ll also provide you with some useful tips on how to maintain your Whirlpool washer and prevent future problems. By the end of this article, you’ll be able to diagnose and repair your Whirlpool washer with confidence and ease.

Identifying Common Whirlpool Washer Issues

Before you start troubleshooting your Whirlpool washer, it’s important to identify the specific problem that you’re facing. Some issues may be obvious, such as a leak or an error code on the display. Others may be more subtle, such as a reduced spin speed or a bad odor. Here are some of the most common Whirlpool washer issues and their possible causes:

  • Washer Not Draining: This could be due to a clogged or kinked drain hose, a faulty drain pump, a blocked coin trap, or a damaged lid switch.
  • Washer Has a Burned Plastic Odor: This could be due to a worn or broken drive belt, a malfunctioning motor, or a faulty electrical component.
  • Washer Leaking: This could be due to a loose or damaged hose connection, a cracked or dirty drain pump filter, a torn or worn tub seal, or an overfilled or unbalanced load.
  • Washer Doesn’t Have Enough Water: This could be due to low water pressure, a clogged or kinked inlet hose, a faulty water inlet valve, or an incorrect water level setting.
  • Spin Cycle Problems: This could be due to an unbalanced or overloaded load, a worn or broken drive belt, a faulty lid switch, a damaged clutch assembly, or a malfunctioning motor control board.
  • Washer Won’t Start: This could be due to a power failure, a tripped circuit breaker, a blown fuse, a defective door latch switch, a faulty timer or control board, or an incorrect cycle selection.
  • Error Codes: These are codes that appear on the display of your Whirlpool washer to indicate a specific fault or malfunction. Each code has a different meaning and requires a different solution.

Washer Not Draining? Try These Whirlpool Troubleshooting Steps

One of the most frustrating Whirlpool washer problems is when the washer doesn’t drain the water at the end of the cycle. This can leave your clothes soaking wet and prevent you from completing your laundry. Fortunately, there are some simple steps you can take to fix this issue and get your washer back to normal. Here’s what you need to do:

  • Check the Drain Hose: The drain hose is the part that connects your washer to the drain pipe or sink. If the drain hose is clogged with lint, debris, or coins, it can prevent the water from flowing out of the washer. To check the drain hose, first unplug your washer from the power source and turn off the water supply valves. Then disconnect the drain hose from the back of the washer and inspect it for any obstructions. If you find any, remove them and rinse the hose with water. You can also use a plumber’s snake or a coat hanger to clear any clogs inside the hose. Make sure to reconnect the hose securely and avoid any kinks or bends that could restrict the water flow.
  • Clean the Drain Pump Filter: The drain pump filter is located at the bottom of your Whirlpool washer and is responsible for catching any foreign objects that may enter the drain system. Over time, the filter can get dirty and clogged with lint, hair, coins, buttons, etc., which can reduce its efficiency and cause drainage problems. To clean the drain pump filter, first unplug your washer from the power source and turn off the water supply valves. Then remove the lower access panel on the front of your washer by unscrewing it with a screwdriver. You’ll see a round knob that is attached to the filter. Place a shallow pan under the filter to catch any water that may spill out. Then turn the knob counterclockwise and pull out the filter. Clean it with warm water and soap and remove any debris that may be stuck inside. Replace the filter by pushing it back into place and turning it clockwise until it locks. Reattach the lower access panel and screw it back on.
  • Check the Door Latch Switch: The door latch switch is a safety device that prevents your Whirlpool washer from spinning or draining if the door is not closed properly. If the switch is faulty or damaged, it may not send the correct signal to the control board and cause the washer to stop working. To check the door latch switch, first unplug your washer from the power source and open the door. Locate the switch on the inside of the door frame and inspect it for any signs of wear or damage. You can also use a multimeter to test the switch for continuity. If the switch is defective, you’ll need to replace it with a new one.
  • Check the Coin Trap: The coin trap is a small plastic device that is attached to the drain hose and is designed to catch any coins or small objects that may enter the drain system. If the coin trap is clogged or blocked, it can prevent the water from draining out of your Whirlpool washer. To check the coin trap, first unplug your washer from the power source and turn off the water supply valves. Then disconnect the drain hose from the back of the washer and locate the coin trap. It should be a white or gray plastic piece with a screw-on cap. Remove the cap and check inside for any coins or debris that may be stuck. If you find any, remove them and rinse the coin trap with water. Replace the cap and reconnect the drain hose securely.
  • Inspect the Drain Pump: The drain pump is an electric device that pumps the water out of your Whirlpool washer during the drain cycle. If the drain pump is cracked, damaged, or burned out, it may leak water or fail to operate properly. To inspect the drain pump, first unplug your washer from the power source and turn off the water supply valves. Then remove the lower access panel on the front of your washer by unscrewing it with a screwdriver. You’ll see the drain pump attached to the bottom of the tub with two hoses and wires. Check for any signs of damage or leakage on the pump and its connections. You can also use a multimeter to test the pump for continuity and resistance. If the pump is defective, you’ll need to replace it with a new one.

Washer Has a Burned Plastic Odor

Another common Whirlpool washer problem is when you notice a burned plastic odor coming from your machine. This can indicate that something is overheating or melting inside your washer, which can be dangerous and damage your appliance. Here are some possible causes and solutions for this issue:

  • Check the Drive Belt: The drive belt is a rubber belt that connects the motor to the transmission and allows your Whirlpool washer to spin and agitate. If the drive belt is worn, broken, or misaligned, it can cause friction and heat up, resulting in a burned plastic smell. To check the drive belt, first unplug your washer from the power source and turn off the water supply valves. Then tilt your washer back and rest it on a sturdy object. You’ll see the drive belt underneath your washer wrapped around two pulleys. Inspect it for any signs of wear, damage, or slippage. If you find any, you’ll need to replace it with a new one.
  • Check the Motor: The motor is an electric device that powers your Whirlpool washer and drives its functions. If the motor is overheating, malfunctioning, or short-circuiting, it can produce a burned plastic smell and damage your appliance. To check the motor, first unplug your washer from the power source and turn off the water supply valves. Then remove the lower access panel on the front of your washer by unscrewing it with a screwdriver. You’ll see the motor attached to one end of the drive belt with wires and connectors. Check for any signs of damage, overheating, or burning on the motor and its connections. You can also use a multimeter to test the motor for continuity and resistance. If you find any problems with your motor, you’ll need to replace it with a new one.
  • Check for Foreign Objects: Sometimes, foreign objects such as coins, buttons, nails, etc., can get stuck inside your Whirlpool washer and cause friction and heat up, resulting in a burned plastic smell. To check for foreign objects, first unplug your washer from the power source and turn off the water supply valves. Then remove any clothing items from your washer and inspect them for any objects that may have fallen out of pockets or seams. You can also check inside your washer tub, drain hose, drain pump filter, coin trap, agitator or impeller (depending on your model), etc., for any objects that may be lodged inside. If you find any foreign objects inside your washer, remove them carefully and dispose of them properly.

Whirlpool Washer Leaking? Follow These Troubleshooting Tips

A leaky Whirlpool washer can be a messy and annoying problem that can damage your floor and waste water. There are several possible reasons why your Whirlpool washer may be leaking water from different parts of your machine. Here are some troubleshooting tips to help you find and fix this issue:

  • Check Hose Connections: One of the most common causes of a leaky Whirlpool washer is a loose or damaged hose connection. Your washer has several hoses that connect it to the water supply, the drain, and the internal components. If any of these hoses are not properly attached, cracked, or punctured, they can leak water and cause a mess. To check the hose connections, first unplug your washer from the power source and turn off the water supply valves. Then inspect the hoses at the back of your washer and look for any signs of damage or leakage. You can also try tightening the hose clamps or replacing the washers if they are worn or corroded. If you find any damaged hoses, you’ll need to replace them with new ones.
  • Check the Drain Pump Filter: As we mentioned earlier, the drain pump filter is located at the bottom of your Whirlpool washer and is responsible for catching any foreign objects that may enter the drain system. If the filter is cracked or dirty, it can leak water and cause your washer to malfunction. To check the drain pump filter, follow the same steps as we described in the previous section on how to clean it. Make sure to replace the filter if it is damaged or broken.
  • Check the Tub Seal: The tub seal is a rubber gasket that seals the gap between the outer tub and the inner tub of your Whirlpool washer. It prevents water from leaking out of your washer during the wash and spin cycles. If the tub seal is torn, worn, or corroded, it can allow water to escape and drip from your washer. To check the tub seal, first unplug your washer from the power source and turn off the water supply valves. Then remove the agitator or impeller (depending on your model) from inside your washer by unscrewing it with a socket wrench or a spanner. You’ll see the tub seal underneath it. Inspect it for any signs of damage or wear. If you find any, you’ll need to replace it with a new one.
  • Check for Overloading or Unbalanced Loads: Sometimes, your Whirlpool washer may leak water because you have overloaded it with too many clothes or because your load is unbalanced. This can cause your washer to vibrate excessively and spill water over the edges of your tub. To prevent this from happening, make sure to follow the manufacturer’s recommendations on how much laundry you can put in your washer and how to distribute it evenly inside your tub. You can also use a level to check if your washer is sitting on a flat and stable surface. If not, you can adjust its feet or use shims to balance it.

Washer Doesn’t Have Enough Water

Another common Whirlpool washer problem is when your washer doesn’t fill up with enough water for your wash cycle. This can result in poor cleaning performance and wasted detergent. There are several possible reasons why your Whirlpool washer may not have enough water, such as:

  • Low Water Pressure: If your water pressure is too low, it may take longer for your Whirlpool washer to fill up with water or it may not fill up at all. This can be due to a clogged or kinked inlet hose, a faulty water inlet valve, or a problem with your plumbing system. To check your water pressure, first unplug your washer from the power source and turn off the water supply valves. Then disconnect the inlet hoses from the back of your washer and place them in a bucket or a sink. Turn on the water supply valves and observe how fast and how much water comes out of each hose. If you notice any low pressure or no water at all, you may need to clean or replace your inlet hoses, check your water inlet valve for any debris or damage, or contact a plumber to fix your plumbing issue.
  • Incorrect Water Level Setting: If you have selected a low water level setting for your wash cycle, your Whirlpool washer may not fill up with enough water for your load size. This can affect how well your clothes are cleaned and rinsed. To avoid this problem, make sure to select an appropriate water level setting for your load size and type of fabric. You can also use an automatic load sensing feature if your model has one. This feature will automatically adjust the water level based on the weight and size of your load.
  • Faulty Water Level Switch: The water level switch is a device that monitors and controls how much water enters your Whirlpool washer during each cycle. It works by sending an electric signal to the timer or control board when the desired water level is reached. If the switch is faulty or damaged, it may not send the correct signal and cause your washer to underfill or overfill with water. To check the water level switch, first unplug your washer from the power source and turn off the water supply valves. Then remove the control panel on the top of your washer by unscrewing it with a screwdriver. You’ll see the water level switch attached to a clear plastic tube that runs to the bottom of the tub. Inspect the switch and the tube for any signs of damage or clogging. You can also use a multimeter to test the switch for continuity and resistance. If you find any problems with your water level switch, you’ll need to replace it with a new one.

Spin Cycle Problems? Whirlpool Washer Troubleshooting Guide

Another common Whirlpool washer problem is when your washer doesn’t spin properly or at all during the spin cycle. This can leave your clothes wet and wrinkled and affect your drying time and energy consumption. There are several possible reasons why your Whirlpool washer may have spin cycle problems, such as:

  • Unbalanced or Overloaded Load: As we mentioned earlier, if you have put too many clothes in your washer or if your load is not distributed evenly inside your tub, your washer may vibrate excessively and fail to spin properly or at all. This can also cause damage to your washer’s components and create noise. To prevent this from happening, make sure to follow the manufacturer’s recommendations on how much laundry you can put in your washer and how to distribute it evenly inside your tub. You can also use a cycle that has a high spin speed or an extra rinse option to remove excess water from your clothes.
  • Worn or Broken Drive Belt: The drive belt is a rubber belt that connects the motor to the transmission and allows your Whirlpool washer to spin and agitate. If the drive belt is worn, broken, or misaligned, it can cause your washer to stop spinning or spin slowly or erratically. To check the drive belt, follow the same steps as we described in the previous section on how to check it. Make sure to replace it if it is damaged or broken.
  • Faulty Lid Switch: The lid switch is a safety device that prevents your Whirlpool washer from spinning if the lid is not closed properly. If the switch is faulty or damaged, it may not send the correct signal to the control board and cause your washer to stop spinning. To check the lid switch, follow the same steps as we described in the previous section on how to check it. Make sure to replace it if it is defective.
  • Damaged Clutch Assembly: The clutch assembly is a device that connects the transmission to the inner tub of your Whirlpool washer. It helps your washer to gradually reach the desired spin speed and stop smoothly at the end of the cycle. If the clutch assembly is damaged or worn out, it may cause your washer to spin too fast or too slow, make noise, or leak oil. To check the clutch assembly, first unplug your washer from the power source and turn off the water supply valves. Then tilt your washer back and rest it on a sturdy object. You’ll see the clutch assembly underneath your washer attached to the transmission shaft with a brake cam driver and a retaining ring. Inspect it for any signs of damage, wear, or oil leakage. You can also use a multimeter to test its resistance. If you find any problems with your clutch assembly, you’ll need to replace it with a new one.
  • Malfunctioning Motor Control Board: The motor control board is an electronic device that controls the speed and direction of your Whirlpool washer’s motor. It works by receiving signals from the timer or control board and sending power to the motor. If the motor control board is malfunctioning or burned out, it may cause your washer to spin erratically or not at all. It may also display an error code on the screen. To check the motor control board, first unplug your washer from the power source and turn off the water supply valves. Then remove the lower access panel on the front of your washer by unscrewing it with a screwdriver. You’ll see the motor control board attached to the bottom of the tub with wires and connectors. Check for any signs of damage, burning, or corrosion on the board and its connections. You can also use a multimeter to test the board for continuity and voltage. If you find any problems with your motor control board, you’ll need to replace it with a new one.

Washer Won’t Start

Another common Whirlpool washer problem is when your washer won’t start at all or won’t complete a cycle. This can be frustrating and prevent you from doing your laundry. There are several possible reasons why your Whirlpool washer may not start, such as:

  • Power Failure: If there is a power outage or a power surge in your area, your Whirlpool washer may not receive enough electricity to operate. To check for a power failure, first make sure that your washer is plugged into a working outlet and that the cord is not damaged or loose. You can also try plugging another device into the same outlet to see if it works. If not, you may need to check your circuit breaker or fuse box and reset or replace any tripped or blown fuses. If the power is restored, you may need to restart your washer by pressing and holding the Start/Pause button for a few seconds.
  • Tripped Circuit Breaker or Blown Fuse: If your Whirlpool washer draws too much current or experiences a short circuit, it may trip the circuit breaker or blow the fuse that protects your electrical system. This can prevent your washer from starting or completing a cycle. To check for a tripped circuit breaker or blown fuse, first unplug your washer from the power source and turn off the water supply valves. Then locate your circuit breaker or fuse box and look for any switches that are in the off position or any fuses that are burned out. You can reset the circuit breaker by flipping it back to the on position or replace the fuse with a new one of the same rating. Then plug your washer back into the power source and turn on the water supply valves. If the problem persists, you may have a faulty electrical component in your washer that needs to be replaced.
  • Defective Door Latch Switch: The door latch switch is a safety device that prevents your Whirlpool washer from starting if the door is not closed properly. If the switch is defective or damaged, it may not send the correct signal to the control board and cause your washer to not start. To check the door latch switch, follow the same steps as we described in the previous section on how to check it. Make sure to replace it if it is defective.
  • Faulty Timer or Control Board: The timer or control board is an electronic device that controls the cycles and functions of your Whirlpool washer. It works by sending signals to various components such as the water inlet valve, the drain pump, the motor, etc., to operate at specific times and durations. If the timer or control board is faulty or damaged, it may not send the correct signals and cause your washer to not start or complete a cycle. It may also display an error code on the screen. To check the timer or control board, first unplug your washer from the power source and turn off the water supply valves. Then remove the control panel on the top of your washer by unscrewing it with a screwdriver. You’ll see the timer or control board attached to the back of the panel with wires and connectors. Check for any signs of damage, burning, or corrosion on the board and its connections. You can also use a multimeter to test the board for continuity and voltage. If you find any problems with your timer or control board, you’ll need to replace it with a new one.

Error Codes Decoded: Whirlpool Washer Troubleshooting

Some Whirlpool washer models have a digital display that shows error codes when something goes wrong with your machine. These error codes are designed to help you identify and troubleshoot the specific problem that your washer is facing. Each error code has a different meaning and requires a different solution. Here are some of the most common error codes and what they mean:

  • LD Error Code: This error code means that your Whirlpool washer is taking too long to drain the water. This can be due to a clogged or kinked drain hose, a faulty drain pump, a blocked coin trap, or a damaged lid switch. To fix this error code, follow the same steps as we described in the previous section on how to fix a washer that is not draining.
  • F1 Error Code: This error code means that there is a problem with the main control board of your Whirlpool washer. This can be due to a power surge, a loose wire, or a defective board. To fix this error code, first unplug your washer from the power source and wait for a few minutes. Then plug it back in and see if the error code clears. If not, you may need to replace the main control board with a new one.
  • F2 Error Code: This error code means that there is a problem with the keypad of your Whirlpool washer. This can be due to a stuck button, a short circuit, or a defective keypad. To fix this error code, first unplug your washer from the power source and wait for a few minutes. Then plug it back in and see if the error code clears. If not, you may need to replace the keypad with a new one.
  • F3 Error Code: This error code means that there is a problem with the temperature sensor of your Whirlpool washer. This can be due to a loose wire, a faulty sensor, or an incorrect water temperature setting. To fix this error code, first unplug your washer from the power source and turn off the water supply valves. Then remove the lower access panel on the front of your washer by unscrewing it with a screwdriver. You’ll see the temperature sensor attached to one of the inlet hoses with wires and connectors. Check for any signs of damage or loose connections on the sensor and its wires. You can also use a multimeter to test the sensor for resistance and compare it with the manufacturer’s specifications. If you find any problems with your temperature sensor, you’ll need to replace it with a new one.
  • F5 Error Code: This error code means that there is a problem with the water level switch of your Whirlpool washer. This can be due to a clogged or kinked pressure hose, a faulty switch, or an incorrect water level setting. To fix this error code, follow the same steps as we described in the previous section on how to check the water level switch. Make sure to replace it if it is faulty.

We hope that we have helped you to troubleshoot some of the most common Whirlpool washer problems and fix them with ease. By following these simple steps and tips, you can save time and money and extend the life of your Whirlpool washer. However, if you encounter a problem that is beyond your skills or requires professional assistance, we recommend that you contact a qualified Whirlpool service technician or call the Whirlpool customer support line for further guidance.

FAQs

Q: How do I reset my Whirlpool washer?

A: If your Whirlpool washer is not working properly or displaying an error code, you may need to reset it to clear the fault and restore its normal function. To reset your Whirlpool washer, follow these steps:

  • Unplug your washer from the power source and wait for a few minutes.
  • Plug it back in and press and hold the Start/Pause button for a few seconds.
  • Release the button and select a new cycle and settings.
  • Press the Start/Pause button again to start your washer.
  • If the problem persists, you may need to contact a Whirlpool service technician or call the Whirlpool customer support line for further assistance.

Q: How do I clean my Whirlpool washer?

A: To keep your Whirlpool washer clean and fresh, you should perform some regular maintenance tasks, such as:

  • Clean the exterior of your washer with a damp cloth and mild detergent. Do not use abrasive cleaners or solvents that may damage the surface.
  • Clean the interior of your washer tub with a washer cleaner or bleach once a month. Follow the manufacturer’s instructions on how to use the cleaner or bleach. Run a hot water cycle without any clothes or detergent to rinse the tub thoroughly.
  • Clean the dispenser drawer with warm water and soap. Remove any detergent residue or buildup that may clog the dispenser. Rinse and dry the drawer before putting it back in place.
  • Clean the door seal with a damp cloth and mild detergent. Wipe away any dirt, mold, or mildew that may accumulate on the seal. Leave the door slightly open after each cycle to allow air circulation and prevent odor.
  • Clean the drain pump filter and coin trap regularly. Follow the same steps as we described in the previous section on how to clean them.

Q: How do I troubleshoot my Whirlpool washer error codes?

A: If your Whirlpool washer displays an error code on the screen, it means that there is a specific problem or malfunction with your machine. Each error code has a different meaning and requires a different solution. To troubleshoot your Whirlpool washer error codes, follow these steps:

  • Identify the error code that appears on your screen. You can refer to our previous section on how to decode some of the most common error codes and what they mean.
  • Follow the suggested solution for each error code. You may need to check or replace some parts of your washer, such as hoses, filters, switches, sensors, etc. You can also refer to our previous sections on how to check and fix some of the most common Whirlpool washer problems.
  • If the error code persists or if you encounter an error code that is not listed in our guide, you may need to contact a Whirlpool service technician or call the Whirlpool customer support line for further assistance.

Please feel free to share your feedback, comments, or questions with us in the comment section below. We would love to hear from you and help you with any queries that you may have.

Leave a Comment